630 Chips/m RGB COB Strip: A Buyer’s Guide
630 Chips/m RGB COB Strip: A Buyer’s Guide
A 630 chips/m RGB COB strip is a flexible LED strip that places red, green, and blue light-emitting chips on a circuit board at a high density, then covers the assembly with a continuous encapsulating layer. The 630 chips/m figure means an average spacing of approximately 1.59 mm between chips, calculated from 1,000 mm per meter. This dense layout can help reduce visible gaps in illuminated lines, but the final appearance and performance still depend on the strip, diffuser, controller, installation, and viewing conditions.
If you want to learn more, please visit our website.
For a successful purchase, confirm more than chip density. Check voltage, power per meter, PCB width, cut interval, color-control compatibility, encapsulation, installation environment, and supplier documentation. In this guide, we explain how to compare specifications, match the strip to an indoor lighting application, and assess supplier and sourcing details before placing an order.
Who This Guide Is For
This guide is for lighting distributors, project contractors, OEM buyers, and designers sourcing RGB linear lighting components for indoor applications. It is especially relevant when a project needs color-changing light in a line, channel, cove, display, or architectural detail. Buyers should use the guide to create a comparable specification before requesting quotations, rather than relying on “630 chips/m” as the only measure of suitability.
Understanding 630 Chips/m RGB COB Strip
What the chip density tells you
COB stands for chip on board: LED chips are mounted directly onto a substrate, with an encapsulating layer applied over the assembly. In an RGB strip, the light source combines red, green, and blue output, which a compatible controller can adjust to create different colors. At 630 chips/m, the average chip pitch is about 1.59 mm, but that calculation does not describe the strip’s cut interval, electrical layout, or optical result.
The continuous encapsulation can make individual light points less apparent than on some visibly spaced LED layouts. However, no chip density alone guarantees a perfectly uniform line. The profile, cover material, mounting distance, selected color, camera exposure, and dimming level can all affect what an observer sees.
Specifications to compare
Product specifications vary by model, so request a current datasheet for the exact configuration being quoted. Compare the following details across suppliers, and make sure each quotation refers to the same voltage, PCB, encapsulation, and control arrangement.
| Specification | Why it matters | What to confirm |
|---|---|---|
| Rated voltage | Determines the compatible power supply and affects wiring and run planning. | Nominal input voltage, permitted operating range, and any feed guidance. |
| Power per meter | Supports power-supply sizing and heat planning. | Rated watts per meter for the selected RGB model and operating conditions. |
| PCB width and construction | Must fit the channel, mounting surface, and project wiring plan. | Overall width, copper or PCB details provided by the supplier, and adhesive option if applicable. |
| Cut interval | Controls how accurately the strip can be trimmed to the installation length. | Marked cut points and whether cut sections remain electrically usable. |
| Control method | Ensures the RGB channels can be controlled as intended. | Channel arrangement, controller compatibility, and connection diagram. |
| Encapsulation and environment | Affects handling, light output, and suitability for the installation location. | Material details and the supplier’s stated indoor-use conditions. |
Match the Strip to the Application
Coves, shelves, and indirect lighting
For coves and concealed linear details, assess the strip together with the aluminum profile or other mounting system. The distance between the light source and the reflecting surface can influence whether a line looks smooth or shows unevenness. Request a sample assembly using the intended profile and cover when visual consistency is important.
Retail displays and feature lighting
RGB COB can suit indoor displays or feature details where color changes are part of the design. Confirm the controller’s channel arrangement and operating method before procurement, then check colors at the brightness levels the project will actually use. If the application also requires white light, ask whether the specified product can provide the required white output or whether a separate white-light source is needed.
Profiles, bends, and installation constraints
Check the strip width against the available channel and confirm how the product may be bent or routed. A flexible strip should not be folded sharply or forced around a radius outside the supplier’s guidance. For long runs, ask the supplier for connection and feed recommendations based on the selected voltage, power, and installation layout rather than assuming one-end feeding will be suitable.
Goto ENTA Lighting to know more.
A Practical Selection Framework
1. Define the visual and control requirements
Start with the purpose of the light: accent, display, architectural feature, or another indoor use. Record the desired colors, dimming behavior, control method, and whether the project needs a dedicated white-light mode. These requirements help determine whether RGB alone is appropriate and make controller discussions more precise.
2. Set the physical and electrical requirements
Measure the installation space and specify the required strip length, profile width, and locations where the strip must be cut. Request the rated voltage and watts per meter for the exact model, then have the project team confirm power-supply capacity and wiring design. Treat the 1.59 mm average chip pitch as a density reference, not as a substitute for the manufacturer’s cut-mark information.
3. Evaluate light appearance with a sample
Ask for a sample of the quoted construction and view it in the intended profile, cover, and mounting position. A 1 m sample is a practical starting length for checking color, brightness, handling, and fit, but it does not replace evaluation of a full installation or electrical design. If the project has strict color or visual requirements, agree on the evaluation method and acceptance criteria before bulk production.
4. Confirm documents and project support
Request a datasheet, wiring information, packaging details, and any available quality or compliance documents relevant to the destination market. Verify that the documents match the offered model and configuration. Ask the supplier to identify which specifications are fixed and which can be discussed as custom options, such as PCB width, lead-wire arrangement, or packaging.
Pricing, MOQ, and Lead Time
The price of a 630 chips/m RGB COB strip depends on the selected electrical and physical configuration, order quantity, packaging, and any customization. A higher chip-density label does not provide enough information to compare cost on its own. For a useful quotation, send the target voltage, watts per meter, PCB width, length per reel, required accessories, destination, and forecast quantity.
Minimum order quantities and production lead times are supplier- and configuration-specific. Ask whether the quoted MOQ applies to a standard model or to a customized build, and whether samples are available before a larger order. Request the estimated schedule for sample approval, production, and dispatch separately, and confirm what changes could affect that schedule.
Supplier Evaluation Checklist
- Does the supplier provide a datasheet for the exact 630 chips/m RGB model?
- Are voltage, watts per meter, cut interval, dimensions, and control connections clearly stated?
- Can the supplier explain the recommended controller and power-supply requirements?
- Can you review a sample in the intended profile or mounting arrangement?
- Are MOQ, sample terms, lead-time estimates, packaging, and shipping responsibilities clear?
- Can the supplier provide documents appropriate to your market and project requirements?
- Is the quotation specific enough to prevent substitutions in PCB, encapsulation, or control layout?
At ENTA Lighting, we work with B2B buyers on indoor lighting specifications and product selection. Share your application, target dimensions, control requirements, and estimated quantity so we can discuss a suitable configuration and clarify which details need confirmation for your project. Buyers should evaluate the final proposal against their installation design and applicable local requirements.
Key Takeaways and Next Steps
A 630 chips/m RGB COB strip has an average chip pitch of approximately 1.59 mm, but density is only one part of the buying decision. Match the strip to the application by confirming voltage, watts per meter, cut interval, dimensions, controller compatibility, and installation conditions. For visual projects, assess a sample in the intended profile instead of relying only on a specification sheet or product photograph.
The next step is to prepare a short project brief with the required length, mounting space, desired colors, control method, and order estimate. Send it with your documentation and sample requests to potential suppliers, then compare quotations on the same specification basis. Contact ENTA Lighting to discuss your requirements and request product information for a 630 chips/m RGB COB strip configuration.
Contact us to discuss your requirements of 630 Chips/m RGB COB Strip. Our experienced sales team can help you identify the options that best suit your needs.


